Showing results: 151 - 165 of 715 items found.
-
CableEye Light Director System -
CAMI Research Inc. (CableEye®)
Our Light Director™ system (patented) provides a computer-guided technique for assembling connectors used in aerospace, medical, and other high-reliability applications. This system uses light fibers driven by super-bright LED lamps to individually illuminate target cavities in the connector being assembled. When the technician enters the wire code printed on unconnected wires, or touches a wire connected at the other end, the CableEye software turns on the appropriate fiber, thereby causing a bright, flashing light to project from inside the target cavity guiding the technician to the proper insertion point. Correct insertion is confirmed by the elimination of light from that location, whereas insertion into an incorrect location leaves the flashing light visible.
-
AudioJog Rack 8 -
CableJoG Ltd
There are 2 rows of 9 LED's corresponding to each of the possible connector pins and one for the screen (or ground) connection. As each pin is activated, the LED's indicate all connections associated with that pin, so that short, open and crossed circuits can be easily found. The LED's also show the possibility of high resistance or leakage connections. 2 LED's indicate a good digital network connection, either Straight through, or Crossed over.
-
REMOTETEST -
StarTech.com USA LLP
Troubleshoot your wiring problems, quickly and affordably with StarTech.com's REMOTETEST, a Specially designed network wire tester that saves valuable time and effort when testing RJ45, RJ11 and BNC cables.
-
72-13550 -
Tenma
*HDMI cable tester with LED status display*Tests for normal/short/open/crossover circuit*Scan/full display testing modes conversion*Single key operation*Manual/auto power off (after 10 minute inactivity)*Low battery indication < 7.2V*HDMI/HDMI-mini interface*9V battery (6F22)*12-month limited warranty *view Terms & Conditions for details
-
-
Item 802 (CB-T2) -
CAMI Research Inc. (CableEye®)
This multi-purpose CBT2 fixture can be used for operator training, tester system verification, and facility verification.
-
TCT-320 -
Tenma
Designed to check and troubleshoot pin connections of HDMI cables. Tests the continuity of each pin of HDMI cable prior to installation to save time on install.
-
CAMI Research Inc. (CableEye®)
A USB Type-C test interface board for CableEye® cable and harness testing systems. Consisting of a daughter board, populated with two USB-C female connectors, it allows users to continuity-check USB Type-C terminated cables using the CableEye tester while seeing the connectors-under-test rendered graphically. The CB26U fits all CableEye models. Configuration A leader in development of PC-based cable and wire harness, continuity, resistance and hipot test systems for over 20 years, CAMI offers the CableEye suite of products complete with accessories – including “connector boards”. The selection of these test fixture boards is constantly growing and is currently numbering over 60 – most of which are populated with ‘families’ of connectors. When pre-populated boards are used, the tester GUI automatically displays a graphic of the connectors under test. Sold as a set of two boards, each CB26U accepts two USB Type-C connectors. In addition to the latest CableEye software, it requires the CB26 small-frame motherboard (Item 756) for operation, and plugs into one of two available slots – two USB-C-connectors can be tested simultaneously. The CB26 (with CB26U) attaches to the tester like a regular connector board. Contact sales@camiresearch.com or +1 (978) 266-2655 for a quote.
-
CB52 -
CAMI Research Inc. (CableEye®)
The CB52 is intended for periodic calibration verification of the Kelvin 4-wire resistance measurement module – an optional, add-on module that may be purchased with any new hipot system, or added to an existing high voltage tester as an upgrade. To ensure that 4-wire resistance measurements remain accurate, CAMI recommends running the verification check every quarter. A 4-wire measurement module that is out of calibration will give inaccurate results. Some (maybe all) resistance measurements will be incorrect. Consequently, it may Pass what should Fail and, conversely, Fail what should Pass. In other words product yield will be contaminated due to unreliable measurements.
-
CX-D12 -
Shenzhen Chuangxin Instruments Co., Ltd.
It’s strictly designed according to IEC60695-11-2, IEC60332-1, GB/T18380.11-2008, GB/T18380.12-2008 etc. Stainless steel screen with a sliding burner handle support for approaching or movingback the flame from the sample under test according to the CEI standards for test on cables.
-
72-9170 -
Tenma
Quickly identify wires and tests continuityFits in any pocket or tool kit Invaluable in all audio, video, network, telecom and electrical installations
-
PHCT55 -
Pyle Audio Inc.
The PHCT55 is a two-piece item that tests telephone wire continuity. Play a test tone on one end and listen on the other, judge continuity, and diagnose break points.
-
CB29H -
CAMI Research Inc. (CableEye®)
CAMI Research Inc. (Acton, MA) announces another new board for its CableEye cable and harness testing systems. Populated with four 16-pole screw terminal blocks, the board addresses high voltage (HiPot) testing to 2100Vdc/1200Vac. Of particular interest to the harness testing market, the CB29H is also available as a transition board variant (CB29AH). The CB29H and CB29AH boards are high voltage versions of the CB29 with the high voltage traces running on inner layers to afford additional safety, and protection from contamination. Each contains four 16-pole screw terminal blocks that will accept bare wires from 12- to 30-gauge in size. The metal jaws firmly grip an inserted wire without damaging or distorting the end, and the space between each terminal block may be used as a wire channel to guide wires neatly to the side. For each channel, a pair of holes is provided through which wire ties may be inserted to hold the wire bundles in place.
-
LANTESTPRO -
StarTech.com USA LLP
The StarTech.com Advanced RJ45 LAN Cable tester allows a single person to test several long cables faster and more efficiently than ever before. The tester uses remote loop-back plugs that each have their own unique ID number that the tester can identify.
-
CAMI Research Inc. (CableEye®)
An add-on option for the CableEye HVX high voltage cable tester series that permits expanded testing for contact and wire resistance as low as 1 mΩ. After checking for opens, shorts, miswires, and resistance limits, the 4-wire Kelvin measurement applies a user-selectable test current from 10 mA to 1 A to determine connection resistance within 1 mΩ. The resistance profile of a model cable may be stored and used as a basis of comparison during later testing to reveal cold solder joints, faulty crimps, recessed pins, pin contact contamination, improper wire gauge, and stress-extruded wire.This option may be purchased with any new HVX tester, or added as an upgrade to any of your existing HVX testers.